Logitech MX Master 2S Mouse Feet Replacement

简介

Use this guide to replace worn-out or damaged feet (also known as skates, glides, slides, or pads) on your Logitech MX Master 2S mouse.

While it’s possible to cleanly remove the feet, you may need replacements if one rips or separates from its adhesive pad.

你所需要的

步骤 1 Soften the mouse feet adhesive

Logitech MX Master 2S Mouse Feet Replacement, Soften the mouse feet adhesive: 步骤 1 中的图像 1，1

Flip the mouse's power switch into the OFF position, unplug any cables, and flip it over so the feet are facing up.
The unique shape of some mice can prevent them from laying flat. If you need to, lay your mouse on a soft towel to prevent wobble.
If you're planning to reuse your existing mouse feet, note that the adhesive needs to be thoroughly heated for them to be cleanly removed.
Heat an iOpener and apply it to the mouse feet for about two minutes.
Alternatively, you can use a hair dryer to soften the mouse feet adhesive.
When using a hair dryer, don't heat the feet for more than a couple seconds at a time—anything hotter than just warm to the touch risks melting or warping the plastic lower case.

编辑

步骤 2 Separate the mouse foot adhesive

Logitech MX Master 2S Mouse Feet Replacement, Separate the mouse foot adhesive: 步骤 2 中的图像 1，3

Logitech MX Master 2S Mouse Feet Replacement, Separate the mouse foot adhesive: 步骤 2 中的图像 2，3

Logitech MX Master 2S Mouse Feet Replacement, Separate the mouse foot adhesive: 步骤 2 中的图像 3，3

Insert an opening pick between the left foot and the lower case.
Go slowly, and make sure the pick slides underneath both the foot and its adhesive pad. These layers separate easily.
If you plan on reusing your mouse feet, be careful not to crease them or separate them from their adhesive pads.
Slide your pick under the foot to separate its adhesive until you can grab it with your fingers.
If the pick feels stuck, apply more heat before continuing.

编辑

步骤 3 Remove the mouse foot

Logitech MX Master 2S Mouse Feet Replacement, Remove the mouse foot: 步骤 3 中的图像 1，2

Logitech MX Master 2S Mouse Feet Replacement, Remove the mouse foot: 步骤 3 中的图像 2，2

在这个步骤中使用的工具：

Tweezers

$4.99

购买

Use a pair of tweezers or your fingers to remove the mouse foot.

编辑

步骤 4 Remove the remaining feet

Logitech MX Master 2S Mouse Feet Replacement, Remove the remaining feet: 步骤 4 中的图像 1，3

Logitech MX Master 2S Mouse Feet Replacement, Remove the remaining feet: 步骤 4 中的图像 2，3

Logitech MX Master 2S Mouse Feet Replacement, Remove the remaining feet: 步骤 4 中的图像 3，3

Repeat the previous two steps for the three remaining feet.

编辑

步骤 5 Reassembly information

Logitech MX Master 2S Mouse Feet Replacement, Reassembly information: 步骤 5 中的图像 1，3

Logitech MX Master 2S Mouse Feet Replacement, Reassembly information: 步骤 5 中的图像 2，3

Logitech MX Master 2S Mouse Feet Replacement, Reassembly information: 步骤 5 中的图像 3，3

For installing new mouse feet or reusing your old ones:
Use a pair of tweezers or a spudger to remove any large chunks of leftover adhesive.
Thoroughly clean the bottom of the mouse with isopropyl alcohol and a lint-free of microfiber cloth. Allow the surface to dry completely.
Peel your new mouse feet away from their adhesive liners and press them firmly into place.

编辑

结论

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow the above steps in reverse order.

另外一个人完成了本指南。