简介
使用本指南可拆卸和更换 iPhone 12 Pro Max 中的后置摄像头。所有相机模块都作为一个整体更换。
你所需要的
-
-
将重叠的透明包装胶带条黏在 iPhone 的后玻璃上，直到覆盖整个手机后部。
-
如果在接下来的几个步骤中无法让吸盘粘在手机上，请将强力胶带（折叠到把手中，然后用它提起后玻璃。
-
-
-
将蓝色手柄拉向铰链以解锁反向钳的手臂。
-
将反向钳手臂滑过 iPhone 的左边缘或右边缘。
-
将吸盘放在靠近 iPhone 底部边缘的位置——一个在正面，一个在背面。
-
向下推吸盘以将吸力施加到所需区域。
-
-
wenn man die Frontkamera nicht tauscht sondern nur anhebt und reinigt, funktioniert Face ID dann noch?
Wenn du beim Aus- und Einbau alles richtig machst, dürfte dabei nichts passieren.
-
-
持续用力拉起吸盘，使屏幕和边框之间形成轻微间隙。
-
将撬片插入屏幕和边框的间隙 。
Be very careful on this step to insert the pick as vertically as possible!!! I ended up separating the glass from the outer frame on this step and destroying the screen. Not a cheap mistake to make!
I just destroyed the screen as well. I try to read these comments for each step but missed this comment section due to skipping down a few steps for not having the opening tool. Really frustrated.
Anthony -
The glue as of the 12 series is incredibly strong. I'm definitely not new to the game and working only with a suction cup, I damaged the screen too, because I couldn't lift it far enough. Therefore, I too had to buy a new screen. 130€ poorer, I would opt for borrowing the display removal kit Apple sells at selfservicerepairs.com. It's around 50 or 60 Euros and worth it.
It must be emphasized that there's a sandwich here with the phone body, plastic bezel, and screen. The plastic bezel isn't visible as it's hidden by the phone's frame until you raise it with the suction cup -- and if the screen lifts off the bezel when you do this you won't see the bezel and you'll insert the pick between the screen and the bezel, destroying the screen. The instructions need to be much more detailed in this area as the consequences are not only expensive but result in long downtime for the phone (my current situation!). iFixit needs to do a much better job of anticipating what could go wrong and providing ways to avoid it!
The fact that Ifixit has not updated these instructions to reflect this SERIOUS pitfall is ridiculously irresponsible.
-
-
-
Maybe show this vital information earlier??
-
-
如果尚未卸下吸盘手柄或反向钳，请立即将其卸下。
-
像书的封面一样从右侧向上旋转显示屏，以打开iPhone。
-
当你在手机上工作时，将显示器靠在东西上，以保持其支撑。
-
-
-
使用撬棒或指甲断开前传感器组件电缆接口的连接。
when lifting up the front sensor assembly cable connector, you should use the flat end of the spudger. Using the pointed end as shown in the picture runs the risk of damaging components on the board and/or the cable connector itself.
-
-
-
用撬棒或指甲将第一个相机电缆接口从其插槽中向上撬起，以断开连接。
-
-
-
使用撬棒的尖端将相机部件从 iPhone 中提出。
-
卸下后置摄像头。
Bullshit! Don’t bother because Apple locked down the iPhone 12 Pro Max rear camera. It’s not possible to replace it. Do so and you’ll either get a warning that it’s a third party camera OR it just won’t work
You will get the notification but the camera will work. If yours doesn't work either you have a bad camera or you did something wrong. Ive done dozens of these replacements with no issues other than the aftermarket camera notification in the settings. It does NOT affect the camera!
-
将新的替换零件与原始零件进行比较——在安装之前，你可能需要转移剩余的组件或从新零件上取下粘性衬板。
'''要重新组装设备，请按相反顺序执行上述步骤。'
将你的电子垃圾带到R2或e-Stewards认证回收商。
维修没有按计划进行吗？尝试一些[[修复后的问题|基本故障排除]，或询问我们的iPhone 12 Pro Max 论坛求助。
将新的替换零件与原始零件进行比较——在安装之前，你可能需要转移剩余的组件或从新零件上取下粘性衬板。
'''要重新组装设备，请按相反顺序执行上述步骤。'
将你的电子垃圾带到R2或e-Stewards认证回收商。
维修没有按计划进行吗？尝试一些[[修复后的问题|基本故障排除]，或询问我们的iPhone 12 Pro Max 论坛求助。
14等其他人完成本指南。
5指南评论
I am having issues with image focusing after replacing the back camera for this model. The camera is able to focus on wide angles but not on 1x zoom or higher. We have reset the device and ensured it is fully up to date and the issue has persisted. My conclusion is that the camera is faulty and I will need a new replacement camera. Anything else I might be missing?
Would this fix a buzzing noise coming from the camera?
I just need to clean dust off the telephoto lens. Is this the only way?
Hat sehr gut funktioniert, dank der Anleitung.
Update: I tested the rear camera replacement with an iFixit part on an iPhone 12 Pro Max running iOS 18.1.1. The camera works right after replacement, even before calibration. I used Repair Assistant to successfully finish calibrating the iFixit part.
Arthur Shi - 回复
